Skip to content

How big a box do you want to fold?

Print a folding box for any size in millimetres: tuck-end or lid, glue flaps and fold lines, with a 3D fold preview.

Inner size of the box

mm

mm

mm

Start from a common box

More options

Card and preview

mm,

Thin card 0.3 mm, cereal box 0.4 mm, corrugated 1.5 to 3 mm.

%

Printable box template

Paper
Orientation
Download

Print at 100% (actual size), not “Fit to page”, so the sheet keeps its real size.

Your box, inner size

60 × 40 × 60 mm

Flat net 217 × 174 mm, printed at full size. Sheets to print: 1.

Print at 100 percent, cut along the thick lines, score and fold on the thin lines and glue the grey flaps. The sizes allow 0.4 mm of card at each fold. Several sheets are taped edge to edge along the overlap strips.

Print a folding box for any size in millimetres: tuck-end or lid, glue flaps and fold lines, with a 3D fold preview.

How to use

  1. Type the inner length, width and height of the box in millimetres and pick a style.
  2. Under More options set the thickness of your card, then drag the fold slider to see the box fold in 3D.
  3. Print at 100 percent. Cut the thick lines, score and fold the thin lines and glue the grey flaps. Tape sheets together when the net needs more than one.

How it works

A box is a flat shape that folds into a solid, called a net. This tool draws the net for the size you give, at its real size, with cut lines, fold lines and the flaps that get glued. The tuck-end style is one piece with a lid that tucks into the front. The lid style is two open trays, a base and a lid that slides over it.

Card has thickness, and every fold uses a little of it. So each panel is the inner measure plus the card thickness, the tuck tab is a little narrower than the opening, and the lid tray is a little larger than the base tray. For a thin card the extra is a fraction of a millimetre, for corrugated board it matters a lot. The sizes are a practical rule for card up to about 1 millimetre, so test a paper copy first.

A net bigger than the paper is split over several sheets. Each has crop marks and an overlap strip, so you trim and tape them edge to edge. The 3D preview folds the very same panels, walls first, then the closures, then the tuck tabs.

Worked example

How wide is the flat net of a 60 × 40 × 60 mm tuck-end box?

  1. Each panel is the inner measure plus the card thickness: 60.4 mm for front and back, 40.4 mm for the sides.
  2. Across the net sit front, side, back and side, plus a 15 mm glue flap on the left.
  3. Add them up: 15 + 2 × 60.4 + 2 × 40.4.

The flat net is 216.6 mm wide.

Method

The result is an estimate based on common rules of thumb, explained under How it works.

Sources and methods

Frequently asked questions

Is the size inner or outer?

Inner. It is the space inside the box for the thing you want to put in it. The outside is a little larger, by the thickness of the card.

What thickness should I use?

Measure your card. Printer paper is about 0.1 mm, thin card 0.3 mm, a cereal box 0.4 mm and corrugated board 1.5 to 3 mm. Heavy board may need score lines before folding.

Which style is easier?

The tuck-end box is one piece with a single glued seam, the lid style has no glue seam on the walls except the small corner tabs, but you make two trays.

The box is bigger than a sheet. What now?

It prints on several sheets with overlap strips and crop marks. Cut along the crop marks, overlap the strips and tape the sheets edge to edge before cutting out the net.

Will it print at the right size?

Print at 100 percent or actual size, not fit to page. Check the 50 mm line on the first sheet with a ruler.

Can I make a cube?

Yes. Give the same length, width and height. For a cube, the lid style works well, and the tuck-end style makes a classic gift box.

Send feedback