Skip to content

How high is your engine's compression ratio?

Static compression ratio from bore, stroke and the combustion chamber, with the head gasket, deck clearance and piston dish or dome.

mm

cc

More options
mm

mm

cc

Compression ratio

11.26:1

A swept volume of 499.6 cc over a clearance volume of 48.71 cc gives a compression ratio of 11.26:1.

Swept volume (one cylinder)
499.6 cc
Clearance volume
53.71 cc
Of which gasket and deck
8.713 cc

Static compression ratio from bore, stroke and the combustion chamber, with the head gasket, deck clearance and piston dish or dome.

How to use

  1. Enter the bore and stroke of one cylinder and the volume of the combustion chamber in the cylinder head, as measured by filling it with liquid from a burette (the "cc-ing" of a head).
  2. Read the compression ratio, with the swept volume and the clearance volume it comes from.
  3. Under More options add the compressed head gasket thickness, the deck clearance and the volume of any dish or dome in the piston, which all change the ratio.

Compression ratio for different chamber volumes (86 × 86 mm cylinder)

Chamber (cc)Clearance volume (cc)Compression ratio
3543.712.4:1
4048.711.3:1
4553.710.3:1
5058.79.5:1
5563.78.8:1
6068.78.3:1
6573.77.8:1

With a 1 mm head gasket and 0.5 mm deck clearance; a smaller chamber raises the ratio.

How it works

The compression ratio says how much the engine squeezes the air and fuel in a cylinder. It compares the largest volume in the cylinder, with the piston at the bottom, to the smallest, with the piston at the top. A ratio of 10:1 means the mixture is squeezed into a tenth of its volume. Higher ratios give more efficiency and power from the same fuel, but make knocking more likely on low-octane petrol.

The formula is r = (V_s + V_c) ÷ V_c. V_s is the swept volume of one cylinder, π/4 × bore² × stroke. V_c is the clearance volume left at the top: the combustion chamber, plus the thin disc of the head gasket and of the deck clearance (each π/4 × bore² × its height), plus the volume of a dish in the piston, minus the volume of a dome. With an 86 × 86 mm cylinder, V_s = 499.6 cm³; a 45 cm³ chamber, a 1 mm gasket (5.8 cm³) and 0.5 mm of deck clearance (2.9 cm³) give V_c = 53.7 cm³, so r = (499.6 + 53.7) ÷ 53.7 = 10.3.

This is the static ratio from geometry. The effective ratio is lower, because the intake valve closes after the piston has started up, and boosted engines run at a much higher real cylinder pressure than the ratio suggests. The gasket is assumed to have the same bore as the cylinder. Based on Heywood, Internal Combustion Engine Fundamentals (2nd ed.), and Wikipedia's article on compression ratio.

Method

No outside data is used: the result is worked out directly from the formula r = (V_s + V_c) / V_c, explained under How it works.

Sources and methods

Frequently asked questions

What is a good compression ratio?

Most petrol cars run between about 9:1 and 13:1, diesels between about 14:1 and 22:1. The right value depends on fuel octane rating, cooling and whether the engine is turbocharged.

How do I measure the combustion chamber volume?

Fit the spark plug, lay the head level, cover the chamber with a clear plate and fill it with liquid from a burette. The volume of liquid in cc is the chamber volume.

How does a thicker head gasket change the compression ratio?

It adds clearance volume and lowers the ratio. At 86 mm bore each extra millimetre of gasket adds about 5.8 cm³, which here costs roughly 0.9 of a ratio point.

Why do turbo engines have a lower compression ratio?

Boost already raises the cylinder pressure, so a lower static ratio keeps it from knocking. Many turbo petrol engines sit between 8:1 and 10.5:1.

Is this the same as the effective or dynamic compression ratio?

No. This is the static ratio from the geometry. The dynamic ratio also considers when the intake valve closes and is lower, so it is not given here.

Send feedback