Skip to content

How big is your engine?

Engine displacement in cc, litres and cubic inches from bore, stroke and number of cylinders, or the stroke for a target size.

Find

mm

Displacement

1,998 cm³

4 cylinders of 86 mm bore and 86 mm stroke displace 1,998 cm³, or 1.998 L.

In litres
1.998 L
In cubic centimetres
1,998 cm³
In cubic inches
121.9 in³
Per cylinder
499.6 cm³
Bore to stroke
1.00, square

Engine displacement in cc, litres and cubic inches from bore, stroke and number of cylinders, or the stroke for a target size.

How to use

  1. Enter the bore (the cylinder diameter), the stroke (how far the piston travels) and the number of cylinders.
  2. Read the displacement in cubic centimetres, litres and cubic inches, plus the volume of one cylinder and whether the engine is oversquare or undersquare.
  3. To design the other way round, choose Stroke under Find, then enter the displacement you are aiming for.

Engine displacement for common cylinder counts, bores and strokes

Cylinders × bore × strokeDisplacement (cm³)LitresCubic inches
3 × 71 × 84 mm9981.061
4 × 79 × 81.4 mm1,5961.697
4 × 86 × 86 mm1,9982.0122
6 × 82 × 94.6 mm2,9983.0183
8 × 92.2 × 92.7 mm4,9515.0302
8 × 101.6 × 88.4 mm5,7335.7350

The last row is the classic 350 cubic inch V8 (4.00 × 3.48 inches).

How it works

Engine displacement is the volume the pistons sweep as they move from the bottom to the top of their travel, added up over all cylinders. It is the number behind a "2.0 L" badge or a "350 cubic inch" V8, and a rough measure of how much air and fuel the engine can swallow in one cycle.

One cylinder is a cylinder in the geometric sense: its base is a circle of diameter B (the bore) and its height is the stroke S, so its swept volume is V = π/4 × B² × S. Multiply by the number of cylinders N for the engine: V = N × π/4 × B² × S. For four cylinders of 86 mm bore and 86 mm stroke, V = 4 × 0.7854 × 86² × 86 mm³ = 1 998 cm³, sold as a 2.0 litre. Solving the same formula for S gives the stroke that reaches a target size.

An engine whose bore is larger than its stroke is called oversquare: it can rev higher for the same piston speed. A long stroke (undersquare) tends to favour low-down torque. Rated sizes are rounded, and manufacturers use slightly different bores and strokes for the same badge. The result does not include the combustion chamber, which is the clearance volume, nor rotary or two-stroke port effects. Based on Heywood, Internal Combustion Engine Fundamentals (2nd ed.), and Wikipedia's article on engine displacement.

Method

No outside data is used: the result is worked out directly from the formula V = N × π/4 × B² × S, explained under How it works.

Sources and methods

Frequently asked questions

What does engine displacement mean?

It is the total volume swept by all the pistons in one full stroke, usually written in litres or cubic centimetres (cc). A 2.0 L engine sweeps about 2000 cm³.

How many cubic inches is a litre?

One litre is 61.02 cubic inches, so a 5.7 L engine is about 350 cubic inches. The calculator shows all three units at once.

What is the difference between oversquare and undersquare?

Oversquare means the bore is wider than the stroke is long; undersquare means the stroke is longer than the bore. Oversquare engines suit high revs, undersquare ones are often used where low-end pull matters.

Is displacement the same as engine power?

No. Displacement only sets how much air the engine can move per cycle. Power also depends on revs, intake, fuel, boosting and efficiency, so a small turbo engine can out-power a larger one.

Why is my engine's real size not exactly the number on the badge?

Badges are rounded, so a 1998 cm³ engine is sold as a 2.0 L. Tax classes and race classes may use their own rounding or limits, so check the official figure.

Send feedback