What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
Lean angle
8.1°
At 60 km/h (37 mph) round a curve of 200 m radius the ideal lean angle is 8.1°.
- Speed
- 60 km/h (37 mph)
- Grip needed
- μ ≥ 0.57
- Load on the tyres
- 1.15 × weight
- Typical for
- spirited road riding, 25–40°
The ideal lean angle for a speed and curve radius, or the speed a lean angle allows, with the grip it needs.
How to use
- Enter your speed and the radius of the curve. A tight bend can be 25 to 50 metres, a fast sweeper 200 metres or more.
- Read the ideal lean angle, the grip the tyres need and how heavily they are loaded.
- To see how fast a given lean allows, choose Speed under Find and enter the angle instead.
Ideal lean angle for common speeds and curve radii
| Speed (km/h) | 25 m radius | 50 m radius | 100 m radius | 200 m radius |
|---|---|---|---|---|
| 30 | 16° | 8° | 4° | 2° |
| 50 | 38° | 21° | 11° | 6° |
| 70 | 57° | 38° | 21° | 11° |
| 90 | 69° | 52° | 33° | 18° |
| 110 | 75° | 62° | 44° | 25° |
| 130 | 79° | 69° | 53° | 34° |
tan θ = v² ÷ (g × r); the ideal angle of the combined centre of mass from the vertical.
How it works
To go round a curve a bike needs a sideways force that bends its path. The only source is the road pushing on the tyres, and the rider leans in so that the combined force of gravity and the sideways push lines up with the bike and rider. The faster the speed and the tighter the curve, the more the rider has to lean.
The balance is tan θ = v² ÷ (g × r), where θ is the lean angle from the vertical, v the speed in metres per second, r the radius of the curve in metres and g = 9.81 m/s². At 60 km/h (16.7 m/s) round a 50 m curve, tan θ = 277.8 ÷ 490.3 = 0.567, so θ = 29.5°. The same number is the sideways acceleration in g, and the tyres need at least that friction coefficient with the road. The load on the tyres is the weight divided by cos θ, here 1.15 times.
This is the ideal angle of the line through the tyre contact patch and the centre of mass of bike and rider together. A rider who hangs off the bike leans the bike itself less, and wide tyres move the contact patch, so a real bike shows a different angle. The calculation also assumes constant speed, a flat road and no braking or acceleration. Based on OpenStax University Physics, volume 1, section 6.3.
Sources
Frequently asked questions
What lean angle is normal on the road?
Most riding stays below 25 to 30 degrees. Brisk riding reaches 35 to 40, and racing tyres on a dry track can hold 50 degrees or more.
Does a heavier bike lean more?
No. Mass cancels out of the formula: the lean angle depends only on speed and the radius of the curve, not on the weight of the bike or the rider.
What grip do I need for a given lean angle?
The tyres need a friction coefficient of at least tan θ. A lean of 45 degrees needs 1.0, which dry road tyres can reach but wet or dirty asphalt cannot.
Does the same formula work for a bicycle?
Yes, it holds for any single-track vehicle in a steady curve. Bicycles seldom exceed a few tens of degrees on the road, since pedals and tyres limit them.
Why is the angle on my bike's lean meter different?
The meter measures the frame, while this calculator gives the angle of the combined centre of mass. A tyre's width and the rider's body position make the two differ by several degrees.
Next you might need
More in Vehicles
- AdBlue use calculator, private, runs on your device
- Battery percent to kWh and km, private, runs on your device
- Compression ratio calculator, private, runs on your device
- Dashboard warning lights, private, runs on your device
- E-bike range calculator, private, runs on your device
- E85 break-even price calculator, private, runs on your device





