How fast does a capacitor charge or discharge?
The time constant, the voltage at any moment of charging or discharging, and the cut-off frequency.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
More options
Capacitor voltage
3.161 V
After 1 s the capacitor has charged to 3.161 V, 63.2% of 5 V. One time constant τ = R × C = 1 s.
Key values as a table
| Time constants | Time | Voltage (V) | Share |
|---|---|---|---|
| τ | 1 s | 3.161 V | 63.2% |
| 2τ | 2 s | 4.323 V | 86.5% |
| 3τ | 3 s | 4.751 V | 95% |
| 4τ | 4 s | 4.908 V | 98.2% |
| 5τ | 5 s | 4.966 V | 99.3% |
- Time constant τ
- 1 s
- Time to charge 99%
- 4.605 s
- Current at that time
- 0.1839 mA
- Cut-off frequency
- 0.1592 Hz
The time constant, the voltage at any moment of charging or discharging, and the cut-off frequency.
How to use
- Enter the resistance and capacitance in the units on your parts.
- Enter the moment you care about. Drag the point along the curve to watch the voltage change over time.
- Under More options, switch between charging and discharging, set the voltage (5 V by default) and how far along you need to be (99 % by default) to see how long that takes.
How it works
A capacitor charging through a resistor fills quickly at first and then ever more slowly: the closer it gets to the supply voltage, the smaller the voltage left across the resistor, so the less current flows to charge it. Discharging is the mirror image. Both follow an exponential curve set by one number, the time constant.
The time constant is τ = R × C, with R in ohms and C in farads giving seconds. While charging, V(t) = V₀ × (1 − e^(−t/τ)); while discharging, V(t) = V₀ × e^(−t/τ), where V₀ is the supply or starting voltage and e ≈ 2.718. With 10 kΩ and 100 µF, τ = 10 000 × 0.0001 = 1 s, so after 1 s a 5 V supply has charged the capacitor to 5 × (1 − e^(−1)) = 3.16 V, 63 % of the way. Each further τ closes 63 % of the gap that is left: 86 % at 2τ, 95 % at 3τ and over 99 % at 5τ.
The same pair used as a filter passes frequencies below about f = 1 ÷ (2πRC) and weakens those above it. Real capacitors have tolerances of 10 % or more and some leakage, so treat the times as estimates. Source: OpenStax University Physics, volume 2, section 10.5.
Sources
- OpenStax University Physics, vol. 2, §10.5 RC CircuitsUsed for: formula
Frequently asked questions
Does changing the supply voltage change the time constant?
No. With the same ideal resistor and capacitor, the time constant stays the same. A higher supply changes the voltage and current, but not the time to reach the same percentage.
How long until a capacitor is fully charged?
In theory never, because the curve only approaches the supply. In practice five time constants is taken as fully charged: the capacitor is then at 99.3 %.
How do I make a delay of a given time?
Choose a capacitor and change the resistance until the time to reach your switching level (under More options, as a percentage) matches the delay. A circuit that switches at two thirds of the supply waits about 1.1 τ.
What is the cut-off frequency of an RC filter?
The frequency 1 ÷ (2πRC) at which the filter passes about 71 % of the signal's voltage (−3 dB). Below it a low-pass RC filter lets the signal through; above it the signal falls off.
In discharge mode, does 99% done mean 99% of the voltage remains?
No. It means 99% of the initial voltage has been lost, leaving 1%. The percentage is progress through the discharge, not the remaining voltage.
Next you might need
More in Electronics & cabling
- AC power calculator, private, runs on your device
- Battery life calculator, private, runs on your device
- Battery sizes, private, runs on your device
- LED resistor calculator, private, runs on your device
- Logic gates, private, runs on your device
- Resistor colour code calculator, private, runs on your device





