How much voltage comes out of your divider?
Find the output of two resistors, or the resistor that gives the voltage you want, with standard values.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
More options
Output voltage
3.837 V
12 V across 10 kΩ and 4.7 kΩ gives 3.837 V at the tap, 32% of the input, with 0.8163 mA flowing.
Key values as a table
| Resistor | Resistance | Voltage across it |
|---|---|---|
| Upper resistor R1 | 10 kΩ | 8.163 V |
| Lower resistor R2 | 4.7 kΩ | 3.837 V |
- Share of the input
- 32%
- Current drawn
- 0.8163 mA
- Power in the divider
- 9.796 mW
Find the output of two resistors, or the resistor that gives the voltage you want, with standard values.
How to use
- Choose what to find: the output voltage, or the upper resistor R1 or lower resistor R2 that gives the output you want.
- Enter the input voltage and the resistors you know, each in Ω, kΩ or MΩ. Drag the split point in the drawing to try other ratios.
- If something is connected to the output, enter its resistance under More options, and pick the E series of the resistors you have.
How it works
Two resistors in series share the input voltage in proportion to their resistance: the same current flows through both, so the bigger resistor gets the bigger part of the voltage. Taking the output from the point between them gives a fixed fraction of the input.
The output is Vout = Vin × R2 ÷ (R1 + R2), where Vin is the input voltage, R1 the resistor from the input to the output and R2 the one from the output to ground. With 12 V across 10 kΩ and 4.7 kΩ, Vout = 12 × 4.7 ÷ 14.7 = 3.84 V. Turned around, R1 = R2 × (Vin ÷ Vout − 1), so 5 V from 12 V with R2 = 10 kΩ needs R1 = 14 kΩ; the nearest standard E24 value, 15 kΩ, gives 4.80 V.
Anything connected to the output sits in parallel with R2 and pulls the output down, so a divider only stays accurate when the load is much larger than R2, about ten times or more. A divider is fine for a reference or a sensor input but not as a power supply, because the output sags under load and the resistors waste power. Source: OpenStax University Physics, volume 2, section 10.2, and the IEC 60063 E series.
Worked example
What does a divider with R1 = 10 kΩ and R2 = 4.7 kΩ output from 12 V?
- Ratio: R2 ÷ (R1 + R2) = 4.7 ÷ (10 + 4.7) = 0.32.
- Vout = Vin × ratio = 12 × 0.32 = 3.84 V.
3.84 V, with 0.82 mA flowing through the divider.
Sources
Frequently asked questions
Which resistor is R1?
R1 connects the input supply to the output junction. R2 connects that junction to ground, and the output is measured across R2.
Does a load value of zero short the output?
No. In this tool, zero means no load is connected; a short circuit is not modelled by that setting.
Can I swap the resistors?
Yes, but the output changes unless they are equal. The output is always measured across the lower resistor, R2.
Does the nearest standard resistor give exactly my target voltage?
Usually not. When solving for a resistor, compare the exact value with the output shown for the nearest standard value.
Does this include resistor tolerances?
No. It assumes exact resistance values, so actual component tolerances and temperature changes can shift the measured output.





