Skip to content

How strong is this signal in other units?

Convert dBm, dBW, dBµV, dBmV, watts and microvolts for a 50 or 75 ohm system.

dBm

Ω

dBµV

6.99 dBµV

−100 dBm is 100 fW, which is 2.236 µV RMS across 50 Ω.

dBW
−30 dBW
Power
1 mW
dBmV
46.99 dBmV
Voltage (RMS)
223.6 mV

Convert dBm, dBW, dBµV, dBmV, watts and microvolts for a 50 or 75 ohm system.

How to use

  1. Pick the unit you have (dBm, dBW, dBµV, dBmV, watts or volts) and type the level.
  2. Set the system impedance: 50 ohms for radio and test gear, 75 ohms for video and cable TV.
  3. Read the same level in every other unit; the headline shows the one most often needed next.

Signal levels in a 50 ohm system

dBmPower (mW)Level (dBµV)Voltage (µV)
−1001 × 10⁻¹⁰72.24
−735.01 × 10⁻⁸3450.1
−500.0000157707
−300.001777,070
01107224,000
1010117707,000
201001272,240,000
301,0001377,070,000
4010,00014722,400,000

In a 75 ohm system the dBµV values are 1.76 higher for the same power.

How it works

Radio engineers state a signal level as power in decibels against a fixed reference, because levels span many orders of magnitude: a transmitter may put out +40 dBm (10 W) while a receiver hears −100 dBm (0.1 pW). Cable TV and field-strength work state the voltage instead, in dBµV or dBmV. The two are tied together by the impedance of the system, because power is voltage squared divided by resistance.

The power is P = 1 mW × 10^(dBm/10), the RMS voltage across the impedance Z is V = √(P × Z), and dBµV = 20 × log₁₀(V / 1 µV). That makes dBµV = dBm + 90 + 10 × log₁₀(Z): 0 dBm is 106.99 dBµV in a 50 Ω system (a rule of thumb says +107) and 108.75 dBµV in a 75 Ω one. dBmV is 60 dB lower than dBµV. Example: 0 dBm = 1 mW = 223.6 mV across 50 Ω.

The conversion assumes a matched, purely resistive system and a sine wave (RMS values). Peak or peak-to-peak voltages are larger by √2 or 2√2. Sources: Wikipedia on the decibel and dBm, and the ARRL Handbook.

Sources

Sources and methods

Frequently asked questions

What is the difference between dBm and dBW?

Both are power relative to a reference: dBm is relative to one milliwatt and dBW to one watt, so dBW is always 30 less than dBm for the same power.

Why does the answer change between 50 and 75 ohms?

Power does not depend on impedance, but the voltage that carries it does. The same power is a larger voltage across 75 ohms than across 50, so the dBµV value is 1.76 dB higher.

Is dBm an absolute level?

Yes: 0 dBm is exactly 1 mW. A bare dB is only a ratio between two levels, which is why signal strengths on receivers are shown in dBm.

What do −70 or −90 dBm mean on Wi-Fi?

They are received powers of 100 pW and 1 pW. Around −67 dBm is considered good enough for video streaming, and below about −80 dBm the link becomes unreliable.

Can I use this for audio levels?

Not directly. Audio uses dBu and dBV against fixed voltages; see the audio levels converter for those.

Send feedback