How strong is this signal in other units?
Convert dBm, dBW, dBµV, dBmV, watts and microvolts for a 50 or 75 ohm system.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
dBµV
116.99 dBµV
10 dBm is 10 mW, which is 707.1 mV RMS across 50 Ω.
- dBW
- −30 dBW
- Power
- 1 mW
- dBmV
- 46.99 dBmV
- Voltage (RMS)
- 223.6 mV
Convert dBm, dBW, dBµV, dBmV, watts and microvolts for a 50 or 75 ohm system.
How to use
- Pick the unit you have (dBm, dBW, dBµV, dBmV, watts or volts) and type the level.
- Set the system impedance: 50 ohms for radio and test gear, 75 ohms for video and cable TV.
- Read the same level in every other unit; the headline shows the one most often needed next.
Signal levels in a 50 ohm system
| dBm | Power (mW) | Level (dBµV) | Voltage (µV) |
|---|---|---|---|
| −100 | 1 × 10⁻¹⁰ | 7 | 2.24 |
| −73 | 5.01 × 10⁻⁸ | 34 | 50.1 |
| −50 | 0.00001 | 57 | 707 |
| −30 | 0.001 | 77 | 7,070 |
| 0 | 1 | 107 | 224,000 |
| 10 | 10 | 117 | 707,000 |
| 20 | 100 | 127 | 2,240,000 |
| 30 | 1,000 | 137 | 7,070,000 |
| 40 | 10,000 | 147 | 22,400,000 |
In a 75 ohm system the dBµV values are 1.76 higher for the same power.
How it works
Radio engineers state a signal level as power in decibels against a fixed reference, because levels span many orders of magnitude: a transmitter may put out +40 dBm (10 W) while a receiver hears −100 dBm (0.1 pW). Cable TV and field-strength work state the voltage instead, in dBµV or dBmV. The two are tied together by the impedance of the system, because power is voltage squared divided by resistance.
The power is P = 1 mW × 10^(dBm/10), the RMS voltage across the impedance Z is V = √(P × Z), and dBµV = 20 × log₁₀(V / 1 µV). That makes dBµV = dBm + 90 + 10 × log₁₀(Z): 0 dBm is 106.99 dBµV in a 50 Ω system (a rule of thumb says +107) and 108.75 dBµV in a 75 Ω one. dBmV is 60 dB lower than dBµV. Example: 0 dBm = 1 mW = 223.6 mV across 50 Ω.
The conversion assumes a matched, purely resistive system and a sine wave (RMS values). Peak or peak-to-peak voltages are larger by √2 or 2√2. Sources: Wikipedia on the decibel and dBm, and the ARRL Handbook.
Sources
- Wikipedia: DBmUsed for: formula
- Wikipedia: DecibelUsed for: formula
Frequently asked questions
What is the difference between dBm and dBW?
Both are power relative to a reference: dBm is relative to one milliwatt and dBW to one watt, so dBW is always 30 less than dBm for the same power.
Why does the answer change between 50 and 75 ohms?
Power does not depend on impedance, but the voltage that carries it does. The same power is a larger voltage across 75 ohms than across 50, so the dBµV value is 1.76 dB higher.
Is dBm an absolute level?
Yes: 0 dBm is exactly 1 mW. A bare dB is only a ratio between two levels, which is why signal strengths on receivers are shown in dBm.
What do −70 or −90 dBm mean on Wi-Fi?
They are received powers of 100 pW and 1 pW. Around −67 dBm is considered good enough for video streaming, and below about −80 dBm the link becomes unreliable.
Can I use this for audio levels?
Not directly. Audio uses dBu and dBV against fixed voltages; see the audio levels converter for those.
Next you might need
More in Unit conversion
- Length converter, private, runs on your device
- Temperature converter, private, runs on your device
- Area converter, private, runs on your device
- Astronomical distance converter, private, runs on your device
- Bitcoin unit converter, private, runs on your device
- CSS unit converter, private, runs on your device





