How much power does a mismatch reflect?
Convert VSWR, return loss, reflection coefficient and mismatch loss, or start from a load resistance on a 50 or 75 ohm line.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
Return loss
19.08 dB
A VSWR of 1.25 : 1 means a return loss of 19.08 dB; 1.23% of the power is reflected.
- VSWR
- 1.5 : 1
- Reflection coefficient |Γ|
- 0.2
- Mismatch loss
- 0.18 dB
- Power reflected
- 4%
- Power delivered
- 96%
Convert VSWR, return loss, reflection coefficient and mismatch loss, or start from a load resistance on a 50 or 75 ohm line.
How to use
- Choose what you know: the VSWR, the return loss, the reflection coefficient, or a load resistance on a line of known impedance.
- Enter the value; the headline shows the quantity you most likely want next.
- Read the mismatch loss and the share of power reflected and delivered below it.
VSWR, return loss and power reflected
| VSWR | Return loss (dB) | Mismatch loss (dB) | Power reflected (%) |
|---|---|---|---|
| 1.1 | 26.4 | 0.01 | 0.2 |
| 1.25 | 19.1 | 0.05 | 1.2 |
| 1.5 | 14 | 0.18 | 4 |
| 2 | 9.5 | 0.51 | 11.1 |
| 3 | 6 | 1.25 | 25 |
| 5 | 3.5 | 2.55 | 44.4 |
| 10 | 1.7 | 4.81 | 66.9 |
A match better than 1.5:1 reflects under 4 % of the power.
How it works
When a transmission line is not terminated in its own impedance, part of the wave bounces back from the load and forms a standing wave on the line. VSWR (voltage standing wave ratio) is the ratio of the highest to the lowest voltage along that wave: 1:1 is a perfect match, and the bigger the number, the more is reflected. Return loss and mismatch loss say the same thing in decibels.
The reflection coefficient is Γ = (Z_L − Z0) / (Z_L + Z0), where Z_L is the load and Z0 the line impedance. Then VSWR = (1 + |Γ|) / (1 − |Γ|), return loss RL = −20 log₁₀|Γ|, mismatch loss ML = −10 log₁₀(1 − |Γ|²), and the reflected share of power is |Γ|². A 75 Ω load on a 50 Ω line gives Γ = 0.2, VSWR 1.5, RL 14.0 dB and 4 % of the power reflected, a loss of just 0.18 dB.
The tool treats the load as a pure resistance and ignores line loss, which hides reflections on a long lossy cable: a cable's own loss makes the VSWR measured at the radio look better than at the antenna. Sources: Pozar, Microwave Engineering, and Wikipedia on standing wave ratio and return loss.
Sources
- Wikipedia: Standing wave ratioUsed for: formula
Frequently asked questions
What VSWR is good enough for an antenna?
Below 1.5:1 is excellent and below 2:1 is the usual limit for amateur radio; at 2:1 only 11 % of the power is reflected, a loss of about half a decibel.
Is a higher return loss better?
Yes. Return loss measures how far the reflected wave is below the forward wave, so 20 dB (VSWR 1.22) is a better match than 10 dB (VSWR 1.92).
Does reflected power get lost as heat?
Not directly. It travels back toward the transmitter, where some transmitters fold back their output to protect themselves, and some of it is absorbed by the cable's loss on the way.
Why can the VSWR be 1:1 with a different load impedance?
It cannot: VSWR 1:1 means Γ is zero, so the load equals the line impedance. A mismatch with a reactive part also shows as a VSWR above 1 even if the resistance is right.
Can I use this for 75 ohm video or cable TV?
Yes. Set the line impedance to 75 Ω and enter the load resistance, or enter the VSWR or return loss you measured.





