Skip to content

How much does a material grow when it warms up?

The change in length or volume of steel, concrete, glass, water and more between two temperatures.

Change of

Change

+72 mm

Steel: 100 m going from −20 °C to 40 °C changes by +72 mm, to 100.072 m.

Key values as a table
TemperatureChangeNew size
−20 °C0 mm100 m
−5 °C+18 mm100.018 m
10 °C+36 mm100.036 m
25 °C+54 mm100.054 m
40 °C+72 mm100.072 m
New size
100.072 m
Change in per cent
0.072%
Coefficient α
12 × 10⁻⁶ per K

The change in length or volume of steel, concrete, glass, water and more between two temperatures.

How to use

  1. Choose whether a length or a volume changes, and pick the material, or Other to type your own coefficient.
  2. Enter the size and the temperatures from and to. A drop in temperature gives a negative change: the material shrinks.
  3. Drag the end of the warm bar (or the top of the column) in the drawing to try other final temperatures.

How it works

Warming a material makes its atoms vibrate harder and sit a little further apart, so almost everything grows slightly when it heats up and shrinks when it cools. The change is tiny per degree but adds up over long lengths, which is why bridges have expansion joints and rails are laid with gaps or under tension.

A length grows by ΔL = α × L₀ × ΔT, where α (alpha) is the material's linear expansion coefficient, L₀ the original length and ΔT the temperature change. A volume grows by ΔV = β × V₀ × ΔT, and for a solid β ≈ 3α. Steel has α = 12 × 10⁻⁶ per °C, so a 100 m steel bridge going from −20 °C to 40 °C grows by 0.000012 × 100 × 60 = 0.072 m, 72 mm.

The coefficients are typical values near room temperature; alloys and grades vary, and coefficients drift over wide temperature ranges. Water is the odd one out: it shrinks as it warms from 0 to 4 °C and its β grows with temperature, so for hot water treat the result as a rough guide. The drawing magnifies the change by the factor shown. Source: OpenStax University Physics, volume 2, section 1.3, and coefficients from Wikipedia's thermal expansion table.

Worked example

How much does a 100 m steel beam grow between −20 °C and 40 °C?

  1. Steel expands by α = 12 × 10⁻⁶ per kelvin; ΔT = 40 − (−20) = 60 K.
  2. ΔL = α · L · ΔT = 12 × 10⁻⁶ × 100 × 60 = 72 mm.

72 mm longer, 100.072 m in all.

Frequently asked questions

Are coefficients per degree Celsius and per kelvin interchangeable?

Yes, for temperature differences: a rise of 1 °C is a rise of 1 K. Enter a coefficient of 12 × 10⁻⁶/K as 12 in the custom coefficient field.

Can this calculate the force in a bar whose ends cannot move?

No. It calculates free expansion or contraction. Finding the stress in a restrained bar also needs its elastic properties and how it is supported.

What is Invar?

A nickel-iron alloy that expands about ten times less than steel. It is used where size must not change with temperature, such as measuring tapes, clocks and precision instruments.

Does a hole in a plate get bigger or smaller when heated?

Bigger. The whole plate scales up, the hole included, as if it were a photo enlarged slightly. That is how a heated ring is shrink-fitted onto a shaft.

Should I enter alpha or beta for a custom volume calculation?

Enter the volume coefficient beta when Volume is selected. The tool uses a custom coefficient directly; it only multiplies alpha by three for the listed solid materials.

Send feedback