How many turns does a transformer need for this voltage?
The ideal transformer: turns ratio, output voltage and the currents on both sides. Drag the output voltage and watch the winding grow.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
More options
Secondary voltage
12 V
Steps down 19.17 : 1: 230 V in gives 12 V out. A load of 2 A takes 24 W, drawing 104.3 mA from the supply.
Key values as a table
| Side | Turns | Voltage | Current | Power |
|---|---|---|---|---|
| Primary | 460 | 230 V | 104.3 mA | 24 W |
| Secondary | 24 | 12 V | 2 A | 24 W |
- Turns ratio N₁ : N₂
- 19.17 : 1
- Supply current
- 104.3 mA
- Power to the load
- 24 W
The ideal transformer: turns ratio, output voltage and the currents on both sides. Drag the output voltage and watch the winding grow.
How to use
- Choose what to calculate: the output voltage from the turns, or the turns needed for a wanted voltage.
- Enter the other values, or drag the top of the output voltage bar to try other outputs.
- Read the turns ratio, the current drawn from the supply and the power; under More options set the load current and an efficiency below 100 %.
Windings for a 230 V mains transformer
| Output voltage (V) | Secondary turns | Turns ratio N₁:N₂ | Mains current at 2 A load (mA) |
|---|---|---|---|
| 5 | 10 | 46 | 43 |
| 9 | 18 | 25.6 | 78 |
| 12 | 24 | 19.2 | 104 |
| 24 | 48 | 9.6 | 209 |
| 48 | 96 | 4.8 | 417 |
Ideal transformer with 460 primary turns on 230 V and a 2 A load; real ones draw a little more.
How it works
A transformer is two coils of wire around one iron core. Alternating current in the first coil makes a changing magnetic field in the core, and that changing field induces a voltage in the second coil. Every turn of wire picks up the same voltage, so the coil with more turns has the higher voltage. It only works with alternating current.
The voltages are in the ratio of the turns: V₂ / V₁ = N₂ / N₁, where V is the voltage and N the number of turns of the primary (1, input) and secondary (2, output) coils. An ideal transformer loses no energy, so the power in equals the power out: V₁ I₁ = V₂ I₂, and stepping the voltage down steps the current up. For example, 230 V across 460 turns gives 230 × 24 / 460 = 12 V on a 24-turn secondary; a 2 A load then takes 24 W and draws only 24 / 230 ≈ 0.10 A from the mains.
Real transformers lose a few per cent as heat in the windings and the core, and their output voltage sags a little under load; set the efficiency to see the extra supply current. The equations follow OpenStax University Physics, volume 2, section 15.6 (openstax.org).
Sources
- OpenStax University Physics, vol. 2, §15.6 TransformersUsed for: formula
Frequently asked questions
Why do power lines use such high voltages?
For the same power, a higher voltage means a smaller current, and the heat lost in the wires grows with the square of the current. Step-up transformers raise the voltage for transmission and step-down transformers lower it again near homes.
Can a transformer work on DC?
No. A steady current makes a steady magnetic field, which induces no voltage. A transformer on DC acts only as a coil of wire and can overheat.
Does a step-down transformer make more power?
No. It trades voltage for current: the output current is higher by the same ratio as the voltage is lower, so the power stays the same (or slightly lower, because of losses).
Why does the turns count have decimals?
The calculator gives the exact ratio. A real winding has whole turns, so round to the nearest turn and check the resulting voltage.
What does the turns ratio tell me?
The voltage changes in the same ratio as the turns, and the current in the opposite ratio. A 20:1 step-down turns 230 V into 11.5 V and lets 20 times as much current flow on the output side.





