Skip to content

How do you turn a picture into a fuse bead pattern?

A bead pattern from your picture for Hama, Perler or Artkal: colours, bead counts, pegboards and a real-size printout.

Bead pattern workspace

Drop or open a picture

14.5 × 14.5 cm 29 × 29 beads · pegboards: 1
Size and pegboards
Finished size
14.5 × 14.5 cm
Beads
841
Pegboards of 29 × 29
1 × 1 = 1
Bead spacing
5 mm

Size by

Beads and boards

Your picture stays on this device: it is never uploaded or put in a link. Links carry only the settings.

A bead pattern from your picture for Hama, Perler or Artkal: colours, bead counts, pegboards and a real-size printout.

Your picture now sits beside its bead design: crop, turn or straighten it there, and find the bead counts and printing in their own tabs.

How to use

  1. Choose your beads (Hama Midi, Hama Mini, Perler or Artkal) and a picture (or paste one). It stays on your device.
  2. Set the size in beads or as the finished size, and the pegs on your pegboard: the height follows the picture's shape.
  3. Under Colours, set the most colours, dithering and whether white areas stay empty; crop the picture if you like.
  4. Check the bead preview and the colour list, then print the real-size pattern and lay a clear board on it.

How big is a fuse bead design, and how many 29 × 29 pegboards does it take?

Beads (across × down)Beads in allMidi, 5 mm (cm)Mini, 2.5 mm (cm)Midi boards
29 × 2984114.5 × 14.57.3 × 7.31
40 × 401,60020 × 2010 × 104
58 × 291,68229 × 14.514.5 × 7.32
58 × 583,36429 × 2914.5 × 14.54
87 × 585,04643.5 × 2921.8 × 14.56
100 × 10010,00050 × 5025 × 2516

Before ironing; fused beads shrink slightly. Divide by 2.54 for inches.

How it works

A fuse bead pattern is the picture cut into a grid with one square per peg. Each square takes the average colour of the part of the picture it covers, and that colour is matched to the nearest bead colour of your brand. Nearness is measured the way eyes see colour (the CIEDE2000 colour difference), not by comparing RGB numbers. With a limit on colours, the tool first picks the bead colours that represent the whole picture best, then matches every square to them; colours used for only a few beads are merged into their nearest neighbour.

The finished size is the beads times the bead spacing: midi beads (Hama Midi, Perler, Artkal S) sit 5 mm apart on their pegboards and mini beads 2.5 mm. Pegboards needed = ⌈beads across ÷ pegs per side⌉ × ⌈beads down ÷ pegs per side⌉, so a 58 × 58 design takes four 29 × 29 boards. The printout is at real size, so it can lie under a clear pegboard.

On-screen bead colours are approximations of coloured plastic: check the real beads before you buy. Fused beads shrink a little, so the finished piece is slightly smaller than the chart. Dithering suggests extra shades with scattered beads; it helps photos but makes small details fiddly.

Worked example

How big is a 58 × 58 bead design with midi beads, and how many pegboards does it need?

  1. Size: 58 × 5 mm = 29 cm across and 58 × 5 mm = 29 cm down.
  2. Beads: 58 × 58 = 3,364.
  3. Pegboards of 29 × 29: ⌈58 ÷ 29⌉ × ⌈58 ÷ 29⌉ = 4.

29 × 29 cm, 3,364 beads on 4 boards.

Method

No outside data is used: the tool works only with what you enter, in your browser.

Sources and methods

Frequently asked questions

How big is one Hama or Perler pegboard design?

A large square pegboard has 29 × 29 pegs: with midi beads (5 mm) that is 14.5 cm, about 5¾ in, a side, and 841 beads when full.

How many colours should I use?

Eight to sixteen for cartoons, logos and pixel art; twenty to forty for photos. Fewer colours are easier to sort and to buy; the merge setting removes colours used for only a few beads.

Can I print the pattern at real size?

Yes. The pattern prints at the real bead spacing, with whole pegboards on a page when that takes no extra paper. Print at 100 % without fitting to the page, check the 50 mm line by the colour key, and lay a clear pegboard on the printout.

Do I need to mirror the design?

Only when the side you iron first is the side you will show, for example a design with text that you display flat-side up. Pegboard designs are built as you see them, so for most designs leave it off.

Is my picture uploaded?

No. The picture is read and turned into a pattern in your browser. A shared link carries only the settings, so the other person needs the same picture.

Are the bead numbers exact matches?

They are the nearest colours by colour difference, using approximate on-screen colours of each bead. Real beads look a little different, especially pearl, glitter and transparent ones; check before you buy.

Send feedback