How much epoxy resin do I need?
Resin and hardener for a mould, coaster, river table or flood coat, by volume or weight, with extra for the cup.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
Mix ratio, count and extra
10 % is common; more for thick, sticky resin or many small moulds.
About 1.1 for casting epoxy; the data sheet gives it. It converts between volume and weight.
Resin mix to prepare
660 mL
330 mL resin + 330 mL hardener, mixed 1:1 by volume · about 726 g
Amounts
- Resin (part A)
- 330 mL
- Hardener (part B)
- 330 mL
- Total weight
- 726 g
- Resin in place, without the extra
- 600 mL
Follow the maker's data sheet for the exact ratio, pot life, temperature and ventilation, and wear gloves and eye protection. Measure exactly: a wrong ratio can leave resin that never cures.
Resin and hardener for a mould, coaster, river table or flood coat, by volume or weight, with extra for the cup.
How to use
- Choose a box mould or table, a round mould or a flood coat, and enter its size and the depth of the pour.
- Under the result, enter the maker's mix ratio (for example 1:1, 2:1 or 100:45) and whether it is by volume or by weight.
- Read the total to mix and how much resin and hardener to measure out; set the extra for what stays in the cup.
Resin for a 30 × 20 cm mould, 1:1 by volume, 10 % extra
How it works
Epoxy resin is poured to a volume, so the first step is geometry: a box mould or river table is length × width × depth, a round mould is π × r² × depth (r is half the diameter), and a flood coat is the surface area times the thickness of the coat. Multiply by how many pieces you pour and add an allowance, because some resin always stays in the cup and on the stirrer.
The mix ratio then splits the total. For a ratio of a : b, resin is a / (a + b) of the total and hardener b / (a + b). Ratios by volume and by weight are different things: 100:45 by weight is not 100:45 by volume, because the two parts differ in density. The tool converts between volume and weight with the density of the mixed resin (about 1.1 g/mL for casting epoxy). Example: a 30 × 20 cm mould 1 cm deep holds 600 mL; with 10 % extra that is 660 mL, or 330 mL of each part at 1:1, about 726 g in all.
The numbers are an estimate. Resin systems differ in density and in how deep they may be poured in one layer, pot life and cure time depend on temperature and mass, and an inexact ratio can leave the resin soft or sticky. Follow the data sheet of your product and work in a ventilated space.
Sources
- NIST SP 811: Guide for the Use of the SIUsed for: constants
Frequently asked questions
How do I calculate how much resin I need?
Work out the volume of the mould (length × width × depth, or π × radius² × depth for a round one), add about 10 % and split it by the mix ratio. The calculator does all of that.
Is the mix ratio by volume or by weight?
The data sheet says which. They are not interchangeable: a 100:45 ratio by weight needs a scale, while 1:1 or 2:1 by volume usually uses marked cups.
How much extra resin should I add?
Around 10 % is common, because resin clings to the cup, the stirrer and the mould. Add more for many small moulds or when a shallow pour must flood a surface.
How much resin does a river table take?
Measure the channel as a box (length × average width × depth) and enter it as a box mould. Check the product's maximum pour depth per layer: a deep channel may need several pours.
How much resin do I need for a flood coat?
Choose flood coat and enter the surface size and the thickness, often 1–3 mm. A 2 mm coat over 1 m² is 2 litres before the extra.
Next you might need
More in Arts & crafts
- Brick mosaic maker, private, runs on your device
- Cross-stitch pattern maker, private, runs on your device
- Diamond painting pattern maker, private, runs on your device
- Embroidery thread colour finder, private, runs on your device
- Fuse bead pattern maker, private, runs on your device
- Increase or decrease evenly, private, runs on your device





