Skip to content

How much voltage does a cell make?

The voltage of a galvanic cell from two half-cells, with ΔG°, K and the Nernst equation for other concentrations.

More options
mol/L

mol/L

°C

Standard cell potential E°cell

1.099 V

Zn²⁺/Zn is oxidized at the anode and Cu²⁺/Cu reduced at the cathode: Cu²⁺ + Zn → Cu + Zn²⁺.

Key values as a table
ElectrodeHalf-reactionE°E
CathodeCu²⁺ + 2 e⁻ → Cu+0.337 V+0.337 V
AnodeZn²⁺ + 2 e⁻ → Zn−0.7618 V−0.7618 V
ΔG° = −nFE°
−212 kJ/mol
Equilibrium constant K
1.4 × 10³⁷
Electrons transferred n
2
Formula

E°cell = E°cathode − E°anode = +0.337 V − (−0.7618 V) = 1.099 V

The voltage of a galvanic cell from two half-cells, with ΔG°, K and the Nernst equation for other concentrations.

How to use

  1. Pick the two half-cells of your cell, such as copper and zinc. The order does not matter: the tool finds the cathode.
  2. Read the cell voltage, the overall reaction, ΔG° and K.
  3. Under More options, enter the ion concentrations or the temperature to see the voltage from the Nernst equation.

How it works

A galvanic cell, such as a battery, joins two half-cells. Each has a standard reduction potential E°, measured against the hydrogen electrode at 25 °C with 1 mol/L ions and 1 bar gases. The half-cell with the higher E° takes electrons and is reduced (the cathode); the other gives them up and is oxidized (the anode). The voltage is E°cell = E°cathode − E°anode. In the Daniell cell, E°cell = 0.337 − (−0.762) = 1.099 V, as zinc dissolves and copper plates out.

The voltage also gives the energy and the equilibrium of the reaction: ΔG° = −nFE°cell, where n is the number of electrons moved and F = 96,485 C/mol is the Faraday constant, and K = e^(nFE°/RT). For the Daniell cell, n = 2, so ΔG° = −212 kJ/mol and K ≈ 10³⁷: the reaction runs essentially to completion.

Away from 1 mol/L, the Nernst equation E = E° − (RT/nF) ln Q corrects the voltage, about 0.0592/n volts per tenfold change at 25 °C; this is why a battery's voltage falls as it runs down. The tool varies one ion per half-cell and keeps gases at 1 bar. Real cells also lose voltage to internal resistance and overpotentials. Sources: OpenStax Chemistry 2e, sections 17.3 and 17.4 and Appendix L.

Worked example

What is the voltage of a copper–zinc cell (the Daniell cell) at standard conditions?

  1. Copper has the higher reduction potential, 0.337 V, so it is the cathode; zinc, −0.762 V, is the anode.
  2. E°cell = 0.337 − (−0.762) = 1.099 V.
  3. With n = 2 electrons, ΔG° = −nFE° = −212 kJ/mol, and K is about 10^37.

1.099 V; the reaction runs by itself.

Frequently asked questions

Which electrode is the anode?

In a galvanic cell the anode is where oxidation happens: the half-cell with the lower reduction potential. It is the negative terminal. The cathode, with the higher potential, is where reduction happens and is the positive terminal.

Why do I not multiply E° by the coefficients?

A potential is energy per charge, an intensive property. Doubling a half-reaction doubles both the energy and the electrons, so E° stays the same. Coefficients matter for ΔG° = −nFE° through n, not for E°.

What does a negative cell potential mean?

That the reaction as written does not run by itself: it runs the other way. This tool always picks the direction that gives a positive voltage. To drive the reverse, as in electrolysis or charging a battery, you must apply at least that voltage.

What is a concentration cell?

Two identical half-cells with different ion concentrations. E° is zero, but the Nernst equation gives a voltage: copper in 1 mol/L and 0.01 mol/L Cu²⁺ makes 0.0592 V at 25 °C. Pick the same half-cell twice and change one concentration to try it.

Why is a lead–acid cell about 2 volts?

Its half-cells are PbO₂/PbSO₄ at +1.69 V and PbSO₄/Pb at −0.35 V, so E°cell = 2.04 V. A 12-volt car battery is six such cells in series.

Send feedback