Skip to content

How do you make a buffer of the right pH?

Henderson–Hasselbalch: the pH of a buffer, or the base-to-acid ratio for the pH you want.

Find

mol/L

mol/L

pH

4.94

pH 4.94 is inside the buffer range 3.76–5.76 (pKa ± 1), where the buffer resists added acid and base well.

Key values as a table
[A⁻] / [HA]pH
0.13.76
14.76
105.76
1.54.94
[A⁻] / [HA]
1.5
Buffer range
3.76–5.76

Henderson–Hasselbalch: the pH of a buffer, or the base-to-acid ratio for the pH you want.

How to use

  1. Enter the pKa of the weak acid, for example 4.76 for acetic acid.
  2. To find the pH, enter the concentrations of the conjugate base [A⁻] and the acid [HA]. To design a buffer, choose the ratio and enter the target pH and the total concentration.
  3. Read the pH or the ratio and the amounts, and drag the point along the line to see how the pH follows the ratio.

How it works

A buffer is a weak acid together with its conjugate base, such as acetic acid and acetate. Added acid is taken up by the base and added base by the acid, so the pH barely moves. Its pH depends on the acid's strength and on how much of each form there is.

The Henderson–Hasselbalch equation gives it: pH = pKa + log₁₀([A⁻] ÷ [HA]), where pKa is the acid's strength and [A⁻] and [HA] are the base and acid concentrations. With 0.15 mol/L acetate and 0.10 mol/L acetic acid (pKa 4.76), pH = 4.76 + log₁₀ 1.5 = 4.94. Turned around, a target pH needs the ratio 10^(pH − pKa): pH 5.00 with acetic acid needs 1.74 parts acetate to 1 part acid.

A buffer works best within about one unit of its pKa, where neither form is more than ten times the other; that range is shaded in the drawing. The equation assumes neither form ionizes or reacts much with water, which holds for usual lab concentrations above about 0.01 mol/L, and it ignores activity effects in strong salt solutions. Source: OpenStax Chemistry 2e, section 14.6, Buffers.

Worked example

What is the pH of a buffer with 0.15 mol/L acetate and 0.10 mol/L acetic acid (pKa 4.76)?

  1. Ratio: [A⁻] / [HA] = 0.15 ÷ 0.10 = 1.50.
  2. pH = pKa + log₁₀(ratio) = 4.76 + 0.18 = 4.94.

pH 4.94, inside the useful range of 3.76 to 5.76.

Sources

Sources and methods

Frequently asked questions

Can I use stock-solution concentrations directly?

Use the concentrations after mixing. If the stock solutions have different concentrations or volumes, calculate the moles of each component and divide by the final volume first.

Can this calculate the effect of adding strong acid or base?

Not directly. First account for the neutralization reaction, then enter the remaining acid and conjugate-base concentrations.

What is buffer capacity?

It is how much acid or base a buffer can absorb before its pH changes substantially. Two buffers can have the same pH but different capacities if their total concentrations differ.

Does diluting a buffer change its pH?

Moderate dilution leaves the acid-to-base ratio unchanged, so the calculated pH stays the same while capacity falls. At very low concentrations, this approximation becomes less reliable.

Can I use the same pKa at every temperature?

No. Use a pKa appropriate to the solution temperature, especially for temperature-sensitive buffers such as Tris.

Send feedback