Skip to content

How many sheets of drywall do I need?

Sheets of drywall for walls or a ceiling, with screws, joint tape and joint compound.

m

m

More options

%

Drywall to buy

13 boards

31.5 m² to cover, 1 layer, with 10% extra.

Surface to cover
31.5 m²
Screws
420
Joint tape
38 m
Joint compound
14.2 L

Sheets of drywall for walls or a ceiling, with screws, joint tape and joint compound.

How to use

  1. Choose whether to cover the walls, the ceiling or both, and enter the room's length, width and wall height.
  2. Pick the board size you can buy.
  3. Read the number of boards to buy, then the estimates for screws, tape and joint compound. Under More options you can set the doors and windows to leave out, the layers and the extra for cuts.

Boards for a 4 × 3 m room by wall height (10 % extra, 3.5 m² of openings, 2400 × 1200 mm)

Wall height (m)Surface (m²)Boards
2.430.112
2.531.513
2.734.314
338.515

How it works

Drywall (plasterboard) is sold in boards of a fixed size, so the job is to find the area to cover and divide it by the area of one board. The walls of a rectangular room have an area of 2 × (length + width) × height; the ceiling is length × width. Doors and windows are taken off the walls. The result is multiplied by the layers, increased by an allowance for cuts and breakage, divided by the area of one board and rounded up to a whole board.

Example: a 4 m × 3 m room with 2.5 m walls has 35 m² of wall. Minus 3.5 m² of door and window leaves 31.5 m². With 10 % extra that is 34.65 m², and 2400 × 1200 mm boards of 2.88 m² each give 13 boards. Screws, tape and compound are rules of thumb: about one screw per square foot of board (11 per m²), 370 ft of tape per 1000 ft² (1.2 m per m²) and 9 to 15 gallons of compound per 1000 ft² (here 0.45 L per m², about 11 gallons).

Treat the screws, tape and compound as planning figures: the real amounts depend on how far apart the studs are, the finish level and the product, so check the manufacturer's installation guide. The board count assumes you can cut boards to fit and reuse offcuts; a room full of small walls may need more. This tool counts boards only and does not design the framing.

Frequently asked questions

How many sheets of drywall do I need for a room?

Divide the wall and ceiling area by the area of one board and round up, then add 10 % or so for cuts. A 4 m × 3 m room with 2.5 m walls needs about 13 boards of 2400 × 1200 mm for the walls.

What size are drywall boards?

In most of Europe boards are 1200 mm wide and 2400, 2600 or 2700 mm long. In the US the common sizes are 4 × 8 ft and 4 × 12 ft; 4 × 8 ft is 32 ft² (2.97 m²).

How much waste should I allow for drywall?

About 10 % for a simple room, more for many corners, odd angles or a second layer that you stagger. Offcuts can be used on short walls.

How many screws does a sheet of drywall take?

Roughly 30 to 35 for a 4 × 8 ft board, a little over one per square foot, with the spacing the board maker gives for walls and ceilings. This calculator uses 11 screws per m² of board.

How much joint compound and tape do I need?

A common rule is about 370 ft of tape and 9 to 15 gallons of ready-mixed compound per 1000 ft² of surface, which is 1.2 m of tape and about 0.45 L of compound per m². Two or three coats of compound need the higher end.

Send feedback