How many shingles or roof sheets do I need?
Roof area from the pitch, then shingle bundles or roof sheets, underlayment rolls and ridge caps.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
More options
Roofing to buy
32 bundles
88 m² of roof, 97 m² with 10% extra.
- Pitch
- 25° (×1.1)
- Underlayment
- 2 rolls
Roof area from the pitch, then shingle bundles or roof sheets, underlayment rolls and ridge caps.
How to use
- Enter the length and width of the roof as seen from above, eaves included, and its pitch in degrees, percent or rise per 12.
- Choose shingles or sheets.
- Read the roof area and the bundles or sheets to buy, plus the underlayment rolls. Under More options you can set the extra for cuts, hips and valleys, the coverage of a sheet or roll and the ridge length.
Common pitches: angle and the factor from footprint to roof surface
How it works
A pitched roof is larger than the building it covers, because it slopes. The roof surface is the footprint, the area seen from above with the eaves included, multiplied by the pitch factor √(1 + tan²θ), which is 1 ÷ cos θ for a pitch angle θ. A pitch can be given in degrees, as a percent (rise per 100 of run) or as a rise per 12 of run, the common US way: 6 in 12 is a rise of 6 for every 12 of run, 26.6°.
Example: a 10 m × 8 m footprint at 25° has a factor of 1.103, so the roof is 80 × 1.103 = 88.3 m². With 10 % extra that is 97.1 m². Shingles are sold in bundles, usually three to a square (100 ft², 9.29 m²), so a bundle covers 3.10 m² and you need 32. Underlayment rolls of 50 m² give 2 rolls. In the US a roof is measured in squares: 1 341 ft² is 13.4 squares.
The estimate suits a simple gable or lean-to roof. Hips, valleys, dormers and chimneys add waste, so raise the extra to 15 % or more, and the actual coverage of a bundle, sheet or roll is on the pack. Ridge caps are counted at about 20 linear feet (6.1 m) per bundle. Roof structure, snow load, fixings and weatherproofing are outside this calculator; follow the maker's instructions and local rules.
Sources
- IKO: How Many Square Feet in a Bundle of ShinglesUsed for: reference data
- Inch Calculator: Roofing Material CalculatorUsed for: reference data
Frequently asked questions
How do I calculate roof area from the footprint?
Multiply the footprint, including the eaves, by the pitch factor 1 ÷ cos(angle). A 6:12 roof has a factor of 1.118, a 25° roof 1.103 and a 45° roof 1.414.
How many bundles of shingles are in a square?
Usually three bundles for 100 ft² (9.29 m²) of common three-tab and architectural shingles. Heavier shingles take four or five. Check the packaging.
How much underlayment do I need?
Enough rolls to cover the whole roof area. A roll of synthetic underlayment often covers 1 000 ft² (93 m²) and a roll of 15 lb felt about 400 ft² (37 m²) once overlaps are allowed for.
How much extra should I order?
About 10 % for a simple roof, 15 % or more with hips, valleys and dormers. Keep a few spare bundles for repairs.
What is a roof pitch of 6:12?
The roof rises 6 units for every 12 units of horizontal run, an angle of 26.6° or a slope of 50 %.





