Will it slide down the slope?
The forces on a block on a slope with friction, whether it slides and how fast it speeds up, drawn as arrows live.
What you enter stays on your device while you use this tool. Opening a shared link sends the settings in its address to HowToolbox to prepare the page.
Acceleration down the slope
1.51 m/s²
It slides: the slope pulls it down with 49 N, more than friction can hold (42.5 N), so it speeds up at 1.51 m/s².
Key values as a table
| Force | Size |
|---|---|
| Weight | 98.1 N |
| Pull down the slope | 49 N |
| Normal force | 84.9 N |
| Friction | 34 N |
- Pull down the slope
- 49 N
- Normal force
- 84.9 N
- Friction
- 34 N
- Starts sliding at
- 26.6°
The forces on a block on a slope with friction, whether it slides and how fast it speeds up, drawn as arrows live.
How to use
- Set the slope angle, or drag the top of the slope in the drawing.
- Enter the mass and the two friction coefficients: static friction for a block at rest, sliding friction once it moves.
- See whether the block stays or slides, how fast it speeds up, and every force drawn to scale.
How it works
Gravity pulls the block straight down with its weight, m·g. On a slope that weight splits in two: one part, m·g·sin θ, pulls the block down along the slope, and the other, m·g·cos θ, presses it into the surface. The slope pushes back with the same normal force N, and friction, which can reach μ·N, acts along the surface against the motion.
At rest, friction holds the block as long as m·g·sin θ ≤ μs·m·g·cos θ, that is while tan θ ≤ μs: the block starts to slide at θ = atan μs, whatever its mass. Once it slides, kinetic friction μk·N is usually a little weaker, and the block speeds up at a = g·(sin θ − μk·cos θ). A 10 kg block on a 30° wooden slope (μs 0.5, μk 0.4) feels 49 N down the slope against at most 42 N of static friction, so it slides at 9.81 × (0.5 − 0.4 × 0.866) ≈ 1.5 m/s².
Friction coefficients depend on the materials and their surfaces: about 0.5 for wood on wood, 0.7 for rubber on dry asphalt and under 0.1 for steel on ice, so treat them as estimates. The block is assumed to slide, not roll, without air drag. Formulas from OpenStax University Physics, volume 1, section 6.2 (openstax.org).
Worked example
Does a 10 kg block slide on a 30° slope with friction coefficients 0.5 (static) and 0.4 (sliding)?
- Weight: mg = 98.07 N. Along the slope: mg sin θ = 49.03 N. Normal force: mg cos θ = 84.93 N.
- Most that static friction can hold: 0.5 × 84.93 = 42.46 N, less than 49.03 N, so it slides.
- Acceleration: a = g (sin θ − 0.4 cos θ) = 1.51 m/s².
The block slides down at 1.51 m/s².
Sources
- OpenStax University Physics, vol. 1, §6.2 FrictionUsed for: formula
Frequently asked questions
Can this model a block that is already moving uphill?
No. It starts with a block released from rest and checks whether it slides downhill. An uphill-moving block has friction acting downhill and needs a different force calculation.
How do I measure the coefficient of static friction?
Tilt the slope slowly until the block just starts to move, and read the angle: μs = tan θ. At 27° that is about 0.5.
Why are there two friction coefficients?
Surfaces at rest interlock a little more than surfaces sliding past each other, so it takes more force to start a block moving (static) than to keep it moving (kinetic).
Is static friction always equal to its maximum value?
No. While the block stays at rest, static friction supplies just enough force to balance the pull downhill. Its maximum is the limit before sliding starts.
Can I enter a slope as a percentage grade?
The input takes degrees, not percent. Convert the grade first with angle = arctan(grade ÷ 100); a 100% grade is 45°, not 90°.
Next you might need
More in Physics
- Artificial gravity calculator, private, runs on your device
- Circular motion calculator, private, runs on your device
- Colour mixing: light and paint, private, runs on your device
- Cooling calculator, private, runs on your device
- Coulomb's law calculator, private, runs on your device
- Decibel calculator, private, runs on your device





